Adaptec 2120S - SCSI RAID Controller Guide de l'utilisateur Page 306
- Page / 354
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11-42
Adaptec SCSI RAID Software Reference Guide
As the example shows, the temperature sensor status display
contains the following columns:
■ Enclosure
■ Sensor
■ Temperature
■ Threshold
■ Status
The following sections describe the information that the enclosure
show temperature command can display in these columns.
The Enclosure Column
The Enclosure column displays the ID associated with the enclosure
management device that you specified on the command line. If you
did not specify an ID, the enclosure show temperature
command displays the IDs for all enclosure management devices
connected to the controller. In the example, 0 is specified.
The Sensor Column
The Sensor column displays the unit number associated with the
temperature sensor that you specified on the command line. If you
did not specify a unit number, the enclosure show
temperature command displays the unit numbers for all
temperature sensors on the enclosure management device or
devices.
The Temperature Column
The Temperature column displays the internal enclosure
temperature for this temperature sensor, in degrees Fahrenheit. The
temperature can range from -10 degrees to 245 degrees Fahrenheit.
In the example, the temperature is 70 degrees Fahrenheit.
The Threshold Column
The Threshold column displays the temperature at which an alarm
will be sounded if the temperature goes above the threshold. In the
example, the temperature threshold is 120 degrees Fahrenheit. You
can change the temperature threshold by using the enclosure
set temperature command.
- Adaptec SCSI RAID 1
- 2120S/2200S 1
- Contents 3
- 4 General Control Commands 5
- 5 container Commands 6
- 6 controller Commands 12
- 7 disk Commands 14
- 8 diagnostic Commands 16
- 9 logfile Commands 17
- 10 task Commands 17
- 11 enclosure Commands 18
- Getting Started 23
- Audience 24
- Supported Platforms 24
- Organization 24
- Conventions 25
- Related Documentation 26
- Accessing the Command 27
- Line Interface 27
- ■ From the UNIX/Linux prompt 29
- Syntax and Conventions for 31
- CLI Commands 31
- CLI Command Syntax 32
- Blank Space 34
- CLI Status Information 40
- The Func Item 41
- The Ctr and State Items 42
- General Control Commands 43
- command for 55
- (page 7-9) 61
- ■ Stripe set of mirror sets 62
- ■ Stripe set of volume sets 62
- ■ Stripe set of stripe sets 62
- to indicate that the newly 65
- command: 69
- command 70
- Related Information 101
- Parameters 102
- Switches 102
- Examples 103
- The Dr Column 104
- The Num Label Column 104
- The Total Size Column 105
- The Type Column 105
- The Stripe Size Column 106
- The Usage Column 106
- The Scsi C:ID:L Column 107
- The State Column 107
- The RO Column 108
- The Lk Column 108
- The Task Column 108
- The Done % Column 110
- The Ent Column 110
- The Boot Device Column 111
- The System Files Column 111
- ■ Windows NT 127
- Command Availability 132
- ■ Read Cache Setting 159
- ■ Write Cache Setting 159
- ■ Write Cache Status 160
- In this Chapter 173
- The Battery State Item 176
- The Component Revisions Items 177
- Related Information: 179
- The Targets and Type Items 197
- The C:ID:L Column 206
- The Device Type Column 206
- The Removable media Column 207
- The Rev Column 207
- The Block Column 207
- The Bytes/Block Column 207
- The R/W Column 221
- The Log Errors Column 224
- The Size Column 228
- Parameter 249
- The Task ID Column 253
- The Function Column 253
- The Done% Column 255
- The Array Column 255
- The Specific2 Column 256
- The Enclosure Column 273
- The Fan and Power Columns 273
- The Slot and Sensor Columns 273
- The Door Column 274
- The ScsiId Column 274
- The Speaker Column 274
- The Standard Column 274
- The Diagnostic Column 274
- The State and Status Columns 295
- The scsiId Column 299
- The Insert Column 299
- The Status Column 299
- Enclosure 302
- UpTime D:H:M 302
- PowerCycle 302
- The UpTime D:H:M Column 303
- The PowerCycle Column 303
- The Interval Column 303
- The Sensor Column 306
- The Temperature Column 306
- The Threshold Column 306
- Using the Adaptec Flash 309
- Overview of the AFU 310
- (for example 311
- Firmware Floppy Kit 312
- Running the AFU 313
- AFU Commands 316
- A:\> AFU HELP 317
- A:\> AFU /? 317
- A:\> AFU RESET /C 0 318
- A:\> AFU RESET /C ALL 318
- A:\> AFU UPDATE /C 0 319
- 0...OK. Verifying...OK 320
- AFU Error Handling 321
- Using the Array 323
- Configuration Utility 323
- Running the ACU 324
- Using Interactive Mode 325
- Assigning Array Properties 326
- Managing Arrays 327
- Assigning Hot Spare Drives 328
- Removing Hot Spare Drives 328
- Initializing a Disk Drive 329
- Making an Array Bootable 329
- Using Script Mode 330
- Playback Mode 333
- Initializing Drives 334
- Record Mode 335
- ■ BUILD/VERIFY <n>% 336
- ■ BUILD/VERIFY/CLEAR FAILED 336
- Script File Syntax 337
- The Array Keyword 340
- The Drives Keyword 340
- The Type Keyword 341
- The End Keyword 341
- The HotsparesDrives Keyword 341
- The InitializeAll Keyword 342
- The Method Keyword 343
- The ReadCache Keyword 343
- The Size Keyword 344
- The StripeSize Keyword 344
- The Wait Keyword 344
- The WaitForBuild Keyword 345
- The WriteCache Keyword 345
- Error Handling 346
- Playback and Record Notes 348
- Automated Scripts 351
- Adaptec, Inc 354
- 691 South Milpitas Boulevard 354
- Milpitas, CA 95035 USA 354
Produits connexes et manuels pour Logiciel Adaptec 2120S - SCSI RAID Controller
(14 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels