Adaptec 2120S - SCSI RAID Controller Guide de l'utilisateur Page 277
- Page / 354
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11-13
enclosure Commands
The following example prepares the device in slot 0 on enclosure
management device 0 for insertion or removal as a result of using
the enclosure prepare slot command:
AAC0>enclosure prepare slot 0 0
Executing: enclosure prepare slot 0 0
You may want to use the enclosure show slot command again
to see the change in the device slot’s status, as in the following
example:
AAC0>enclosure show slot
Executing: enclosure show slot
Enclosure Slot scsiId Insert Status
--------- ---- ------ ------- ------------------------------------------
0 0 0:00:0 4 OK UNCONFIG I/R READY NOTACTIVATE
0 1 0:01:0 0 OK UNCONFIG ACTIVATE
0 2 0:10:0 0 OK UNCONFIG ACTIVATE
0 3 0:03:0 0 OK UNCONFIG ACTIVATE
0 4 0:04:0 0 OK UNCONFIG ACTIVATE
1 0 1:00:0 0 OK CONFIG ACTIVATE
1 1 1:01:0 0 OK UNCONFIG ACTIVATE
1 2 1:10:0 0 OK UNCONFIG ACTIVATE
1 3 1:03:0 0 OK UNCONFIG ACTIVATE
1 4 1:04:0 0 OK UNCONFIG ACTIVATE
Note that the Status column now displays I/R READY and
NOTACTIVATE, which means the device slot is off and ready for
the insertion or removal of a device.
Related Information
enclosure commands:
■ enclosure activate slot (page 11-3)
■ enclosure identify slot (page 11-5)
■ enclosure list (page 11-7)
■ enclosure show slot (page 11-33)
- Adaptec SCSI RAID 1
- 2120S/2200S 1
- Contents 3
- 4 General Control Commands 5
- 5 container Commands 6
- 6 controller Commands 12
- 7 disk Commands 14
- 8 diagnostic Commands 16
- 9 logfile Commands 17
- 10 task Commands 17
- 11 enclosure Commands 18
- Getting Started 23
- Audience 24
- Supported Platforms 24
- Organization 24
- Conventions 25
- Related Documentation 26
- Accessing the Command 27
- Line Interface 27
- ■ From the UNIX/Linux prompt 29
- Syntax and Conventions for 31
- CLI Commands 31
- CLI Command Syntax 32
- Blank Space 34
- CLI Status Information 40
- The Func Item 41
- The Ctr and State Items 42
- General Control Commands 43
- command for 55
- (page 7-9) 61
- ■ Stripe set of mirror sets 62
- ■ Stripe set of volume sets 62
- ■ Stripe set of stripe sets 62
- to indicate that the newly 65
- command: 69
- command 70
- Related Information 101
- Parameters 102
- Switches 102
- Examples 103
- The Dr Column 104
- The Num Label Column 104
- The Total Size Column 105
- The Type Column 105
- The Stripe Size Column 106
- The Usage Column 106
- The Scsi C:ID:L Column 107
- The State Column 107
- The RO Column 108
- The Lk Column 108
- The Task Column 108
- The Done % Column 110
- The Ent Column 110
- The Boot Device Column 111
- The System Files Column 111
- ■ Windows NT 127
- Command Availability 132
- ■ Read Cache Setting 159
- ■ Write Cache Setting 159
- ■ Write Cache Status 160
- In this Chapter 173
- The Battery State Item 176
- The Component Revisions Items 177
- Related Information: 179
- The Targets and Type Items 197
- The C:ID:L Column 206
- The Device Type Column 206
- The Removable media Column 207
- The Rev Column 207
- The Block Column 207
- The Bytes/Block Column 207
- The R/W Column 221
- The Log Errors Column 224
- The Size Column 228
- Parameter 249
- The Task ID Column 253
- The Function Column 253
- The Done% Column 255
- The Array Column 255
- The Specific2 Column 256
- The Enclosure Column 273
- The Fan and Power Columns 273
- The Slot and Sensor Columns 273
- The Door Column 274
- The ScsiId Column 274
- The Speaker Column 274
- The Standard Column 274
- The Diagnostic Column 274
- The State and Status Columns 295
- The scsiId Column 299
- The Insert Column 299
- The Status Column 299
- Enclosure 302
- UpTime D:H:M 302
- PowerCycle 302
- The UpTime D:H:M Column 303
- The PowerCycle Column 303
- The Interval Column 303
- The Sensor Column 306
- The Temperature Column 306
- The Threshold Column 306
- Using the Adaptec Flash 309
- Overview of the AFU 310
- (for example 311
- Firmware Floppy Kit 312
- Running the AFU 313
- AFU Commands 316
- A:\> AFU HELP 317
- A:\> AFU /? 317
- A:\> AFU RESET /C 0 318
- A:\> AFU RESET /C ALL 318
- A:\> AFU UPDATE /C 0 319
- 0...OK. Verifying...OK 320
- AFU Error Handling 321
- Using the Array 323
- Configuration Utility 323
- Running the ACU 324
- Using Interactive Mode 325
- Assigning Array Properties 326
- Managing Arrays 327
- Assigning Hot Spare Drives 328
- Removing Hot Spare Drives 328
- Initializing a Disk Drive 329
- Making an Array Bootable 329
- Using Script Mode 330
- Playback Mode 333
- Initializing Drives 334
- Record Mode 335
- ■ BUILD/VERIFY <n>% 336
- ■ BUILD/VERIFY/CLEAR FAILED 336
- Script File Syntax 337
- The Array Keyword 340
- The Drives Keyword 340
- The Type Keyword 341
- The End Keyword 341
- The HotsparesDrives Keyword 341
- The InitializeAll Keyword 342
- The Method Keyword 343
- The ReadCache Keyword 343
- The Size Keyword 344
- The StripeSize Keyword 344
- The Wait Keyword 344
- The WaitForBuild Keyword 345
- The WriteCache Keyword 345
- Error Handling 346
- Playback and Record Notes 348
- Automated Scripts 351
- Adaptec, Inc 354
- 691 South Milpitas Boulevard 354
- Milpitas, CA 95035 USA 354
Produits connexes et manuels pour Logiciel Adaptec 2120S - SCSI RAID Controller
(14 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels