Adaptec 2100S - SCSI RAID Controller Guide de l'utilisateur télécharger pdf (Page 20)

2-9

Storage Manager on ROM

Running SMOR

Start SMOR by pressing Ctrl+A when the RAID controller BIOS

message appears on the screen during the boot sequence. SMOR

starts by displaying its opening screen, as shown in Figure 2-2

(showing the opening screen from a 2400A).

Figure 2-2. SMOR Welcome Window

The letters that appear during the initial device scan process are

The position of a letter corresponds to the device ID assigned to that

device.

CCD

D Hard drive

E SAF-TE, intelligent RAID enclosure, or processor

device

H Hot spare drives

TTape device

0, 1, 5 Physical arrays identified by the RAID level

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 134 135

STORAGE MANAGEMENT 1
SOFTWARE USER’S GUIDE 1
Storage Management Software 2
Copyright 3
Trademarks 3
Disclaimer 3
Contents 7
3 Storage Manager 8
Storage Management 10
Software Overview 10
■ SuSE Linux 6.4 and 7.0 11
■ SCO UNIX/Unixware 11
Storage Manager on ROM 12
Overview 13
Keyboard Reference 14
Menu Reference 15
Icon Reference 17
Screen Layout 17
The Menu Bar 18
The Left Pane – Tree View 18
Running SMOR 20
Controller BIOS Settings 21
Enable Bootable CD-ROMs 22
DOS/Windows 3.1 Cache Setting 22
Scan Delay (SCSI only) 23
EBDA Relocation 23
Enable Extended Int13 23
Information Tab 24
Configuration Tab 26
Mem Address, IRQ 27
PCI MWI Enable 27
Boot Enable 27
Bus Configuration Tab 28
Transfer Rate (SCSI only) 30
Termination (SCSI only) 30
TERMPWR (SCSI only) 30
Device Information Tab 31
Setting the Configuration 36
Array Operations 37
RAID 1 BuildOption: 39
Delete array 40
Hot Spares 41
Rebuilding a Failed Array 42
Creating a SMOR Boot Disk 45
Installing Storage Manager 49
Running Storage Manager 50
Physical Configuration View 51
Logical Configuration View 53
Logical Device Addresses 55
Array Groups 57
Configuration View window 59
Creating an Array Group 61
Naming an Array Group 64
Requirements and Restrictions 65
Expanding an Array Group 66
Status Reporting 68
Information Windows 69
3210S/3400S/3410S Only 71
Flash Configuration Window 74
Device Information Window 76
Device Configuration Window 78
Event Log 80
Event Broadcaster 82
■ Windows 2000 and Windows NT 83
■ NetWare 4.2 and 5.x 83
Windows NT & Windows 2000 84
Formatting Drives – SCSI only 89
Drive Failures 90
Rebuilding a Degraded Array 91
Assigning Hot Spares 92
Running a Verify Process 93
Controller I/O Statistics 94
Cache Statistics 96
Command Statistics 96
Device I/O Statistics 96
Remote Communication 99
Client Workstations 100
Storage Manager 103
Windows 95/98/ME 103
Novell NetWare 103
SCO UNIX 103
Connecting to Remote Systems 104
Making a Manual Connection 106
Using the Phonebook 107
Using a Custom Connection 108
RAIDUTIL Command Line 109
Exit Status 110
Device Address Syntax 110
Command Line Switches 111
Miscellaneous 112
-D Delete logical drives 113
Array Modification 114
RAID Operation 115
Controller-Specific 116
Hot Spare Control 117
-A Alarm status and control 118
-L List devices 119
-P Pagination output 120
-q Quiet mode 120
Introduction 121
Management Information Base 122
Management Console 122
Adaptec MIB Information 123
What’s Included 125
System Requirements 126
Management Consoles 126
SNMP Architecture 128
Adaptec SNMP Subagent 129
Adaptec CI 132
Installing DMI Support 133
Adaptec DMI Modules 133

Commentaires sur ces manuels

Pas de commentaire

Adaptec 2100S - SCSI RAID Controller Guide de l'utilisateur Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Adaptec 2100S - SCSI RAID Controller