Adaptec SAS/SATA/SCSI RAID Controllers Manuel d'utilisateur Page 100
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix E: Using the Adaptec Flash Utility ● 100
6 Complete the flash operation and restart your computer before trying to use the RAID
controller again. (
You can not use your RAID controller while you are
updating its flash.)
Running the
AFU
from the Command Line
Note: You can also run a menu-based AFU (see page 99).
To run the AFU from the command line:
1 Power off your computer, insert the first AFU floppy disk, then power on your computer.
If your computer isn’t set up to boot from the bootable floppy disk, enter the system setup
utility to change the setting.
2 At the DOS command, type AFU followed by a command (see page 100) and any switches
you want.
Note:
To find a controller number, type
AFU LIST
, then press Enter.
The AFU processes the command, prompts you to insert additional floppy disks as needed,
exits, and reports either success or an error message code.
To update a RAID controller’s flash using the command line, see page 103.
AFU Commands
This section lists the available AFU commands.
List
Displays the AFU-supported RAID controllers installed on your computer. Also displays the ID
numbers assigned to each controller.
You don’t have to restart the computer after completing this command.
This example shows a typical system response to a LIST command:
A:\> AFU LIST
Adaptec Flash Utility V4.0-0 B5749
(c)Adaptec Inc. 1999–2005. All Rights Reserved.
Controllers Detected and Recognized:
Controller #0 (03:05:00) Adaptec Adaptec 2230SLP
Save
Saves the contents of a RAID controller’s flash in a UFI file. The name of the UFI file is based
on the controller type and can’t be changed.
You must restart the computer following a SAVE command.
The command syntax for the SAVE command is
AFU SAVE [/C<Controller ID>] [/D <UFI File Path>]
- Installation and User’s Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- System Requirements 14
- About Your RAID Controller 15
- Array-level Features 16
- Adding Enhanced Features 17
- About the Adaptec 4000 18
- About the Adaptec 4800SAS 19
- 256 MB also available 19
- About the Adaptec 4805SAS 20
- About the Adaptec 2420SA 21
- About the Adaptec 2820SA 22
- About the Adaptec 2130SLP 23
- About the Adaptec 2230SLP 24
- Getting Started 25
- Choosing a RAID Level 26
- Selecting Disk Drives 27
- Selecting Cables 28
- SATA Cables 29
- SCSI Cables 29
- Installation Options 30
- Basic Installation Steps 30
- In this chapter 31
- Before You Begin 32
- Installing the Controller 32
- Connecting External Devices 35
- Next Steps 36
- Creating a Bootable Array 37
- Setting the Boot Controller 38
- Creating an Array 38
- Making Your Array Bootable 41
- Installing the Driver and an 42
- Operating System 42
- Creating a Driver Disk 43
- Installing with Windows 44
- Installing with Red Hat Linux 44
- Installing with SUSE Linux 45
- Installing with NetWare 45
- Installing with OpenServer 46
- Installing with Solaris 46
- Installing with UnixWare 47
- Installing with VMWare 47
- Installing with FreeBSD 47
- Installing on Windows 51
- Installing on NetWare 51
- Installing on OpenServer 52
- Installing on Solaris 52
- Installing on UnixWare 53
- Installing on VMWare 53
- Installing on FreeBSD 53
- Managing Your Storage Space 55
- About Adaptec Storage Manager 56
- Which Utility Should I Use? 57
- Solving Problems 58
- Troubleshooting Checklist 59
- Silencing the Alarm 59
- Resetting the Controller 61
- In this appendix 62
- ) Web site at www.scsita.org 62
- What is SAS? 63
- What’s a Phy? 64
- What’s a SAS Port? 65
- What’s a SAS Address? 65
- What’s a SAS Connector? 65
- What do SAS Cables Look Like? 65
- Direct-attach Connections 66
- Backplane Connections 66
- SAS Expander Connections 67
- Understanding RAID 69
- Understanding Drive Segments 70
- Nonredundant Arrays (RAID 0) 70
- RAID 1 Arrays 71
- RAID 1 Enhanced Arrays 71
- RAID 10 Arrays 72
- RAID 5 Arrays 73
- RAID 5EE Arrays 74
- RAID 50 Arrays 75
- RAID 6 Arrays 76
- RAID 60 Arrays 76
- Selecting the Best RAID Level 77
- Using the Adaptec RAID 78
- Configuration Utility 78
- Running the ARC Utility 79
- Managing Existing Arrays 80
- Initializing Disk Drives 80
- Rescanning Disk Drives 80
- Secure Erasing Disk Drives 81
- Opening a -Select Utility 81
- Applying Changes and Exiting 81
- General Controller Settings 82
- Option Description 83
- Viewing the Event Log 85
- Running the ACU Using Scripts 88
- About Record Mode 89
- Required 90
- ? Description 90
- HotspareDrives=0:0:0,0:1:0 91
- Type=Volume 91
- Type=RAID1 91
- ACU exits with an error 92
- Keyword Description 93
- ACU Error Codes 94
- Sample Scripts 95
- Running the Menu-based AFU 99
- Running the 100
- Electrostatic Discharge (ESD) 104
- Environmental Specifications 106
- DC Power Requirements 106
- Current Requirements 106
- Index ● 108 108
- Index ● 109 109
- Index ● 110 110
- Index ● 111 111
- Adaptec, Inc 112
- 691 South Milpitas Boulevard 112
- Milpitas, CA 95035 USA 112
Produits connexes et manuels pour Contrôleurs périphériques Adaptec SAS/SATA/SCSI RAID Controllers
(9 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.343 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels