Adaptec 2930 - SCSI Card Ultra Storage Controller 20 MBps Guide d'installation Page 22
- Page / 86
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
20
VIDAR Film Digitizer Installation Guide
Table-top stand
for the SIERRA™ plus film digitizer
The table-top stand is for use in situations where the SIERRA™ plus
film digitizer cannot be mounted on a wall. The stand was designed to
be placed on a table, desk or countertop up to 36" (91cm) high.
SAFETY WARNING
Never place the SIERRA™ plus with table-top stand on the floor.
In brief, to assemble the SIERRA™ plus film digitizer with the table-top
stand you will:
Assemble the stand and mounting bracket.
Install the digitizer on the mounting bracket.
Place the stand-mounted digitizer in a suitable working location.
Attach power and SCSI cables.
Install the exit tray.
Instructions are provided in this chapter.
Before you start...
Be sure you have already set the SCSI ID and SCSI termination
switches (see the “Configuring SCSI settings” chapter, earlier in this
manual). It’s easier to see and set these switches before the digitizer is
attached to the table-top stand.
- Documentation questionnaire 1
- Comments are from 2
- Installation guide for 3
- Contents 5
- Unpacking 7
- 3. Identify the parts 12
- 4. Remove the shutter lock 15
- 5. If anything is missing 16
- Configuring SCSI settings 17
- SCSI ID switch 18
- Bottom of digitizer 18
- Table-top stand 22
- CAUTION: 24
- Pinch point 24
- Tighten by hand only 24
- 2. Mount the digitizer 25
- SAFETY WARNING 27
- 4. Connect the power cable 28
- 5. Connect the SCSI cable 29
- 6. Install the exit tray 30
- 7. Install the feed tray 31
- Multi-film feed tray cable 32
- To dig iti zer 33
- Power supply 33
- Power cord 33
- Wall mounting 34
- 1. Select proper wall space 35
- WARNING 39
- 4. Mount the digitizer 40
- 5. Connect the power cable 42
- 6. Connect the SCSI cable 43
- 7. Install the exit tray 44
- 8. Install the feed tray 45
- Installing SCSI hardware 48
- 2. Install the SCSI card 50
- Installing SCSI software 52
- Computers with Windows 2000 54
- Computers with Windows 98 56
- Computers with Windows 95 57
- Using the SCSI Utility 59
- Operating 62
- About films 64
- Loading a single film 65
- Loading multiple films 67
- Troubleshooting 69
- In case of difficulty 70
- Operational problems 71
- Appendix 76
- Warranty information 77
- End user information 79
- End user technical contact 79
- System configuration 80
- CD-ROM drive 81
- CD-R/W drive 81
- Diskette drive 81
- Serial ports 82
- USB ports and hub 82
- Parallel ports 82
- Video adapter 83
- Display 83
- SCSI adapters 83
- SCSI devices 84
- Digitizer 84
- Software 85
- Operating system 85
- Scanning software 85
- Scanning parameters 85
Produits connexes et manuels pour Non Adaptec 2930 - SCSI Card Ultra Storage Controller 20 MBps
Non Adaptec AVA-1505A Guide de l'utilisateur
(33 pages)
(33 pages)
Non Adaptec APA-1480 Manuel d'utilisateur
(24 pages)
(24 pages)
Non Adaptec 1394 Guide de l'utilisateur
(80 pages)
(80 pages)
Non Adaptec AHA-2930CU Guide d'installation
(68 pages)
(68 pages)
Non Adaptec 3940UW Guide de l'utilisateur
(82 pages)
(82 pages)
Non Adaptec 1742A Manuel d'utilisateur
(9 pages)
(9 pages)
Non Adaptec SBC-596 Manuel d'utilisateur
(91 pages)
(91 pages)
Non Adaptec ASH-1233 Manuel d'utilisateur
(17 pages)
(17 pages)
Non Adaptec APA-460 Guide d'installation
(58 pages)
(58 pages)
Non Adaptec 39160 Guide d'installation
(38 pages)
(38 pages)
Non Adaptec APA-358 Guide d'installation
(12 pages)
(12 pages)
Non Adaptec AFW-1430 Guide de l'utilisateur
(22 pages)
(22 pages)
Non Adaptec 1742A Manuel d'utilisateur
(68 pages)
(68 pages)
Non Adaptec 2940UW Guide de l'utilisateur
(50 pages)
(50 pages)
Non Adaptec 9110G Spécifications
(38 pages)
(38 pages)
Zanussi ZWG7160P manuels
Manuels d'utilisation et guides de l'utilisateur pour Machines à laver Zanussi ZWG7160P.
Nous fournissons des manuels en pdf 13 Zanussi ZWG7160P à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels