Adaptec ICP5045BL Guide de l'utilisateur Page 84
- Page / 135
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix C: Using the ICP RAID Configuration Utility ● 84
Introduction to the ICP RAID Configuration Utility
The ICP RAID Configuration utility comprises these tools:
● The Array Configuration Utility (ACU)—For creating and managing arrays, and
initializing and rescanning disk drives (see page 84).
Note:
Also available—ACU for DOS. See page 92.
● A -Select Utility—SerialSelect, SATASelect, or SCSISelect, for modifying your controller
and disk drive settings (see page 86).
● Disk Utilities—For formatting or verifying disk drives (see page 90).
Running the ICP RAID Configuration Utility
If your ICP controller is connected to a RAID enclosure, power on your enclosure (or
enclosures) before you power on your computer.
Start or restart your computer. When prompted, press Ctrl+A.
During boot up, if your system has insufficient memory the following message will display.
“ICP RAID Configuration Utility will load after, system initialization. Please wait... Or press
<Enter> Key to attempt loading the utility forcibly [Generally, not recommended]”
Note:
The first time you power on your computer after you install a new controller, the BIOS
may display a configuration that doesn’t match your system’s configuration. This is normal.
Navigating the ICP RAID Configuration Utility
All the tools within the ICP RAID Configuration utility are menu-based and instructions for
completing tasks appear on-screen. Menus can be navigated using the arrows, Enter, Esc, and
other keys on your keyboard.
Using the ACU to Create and Manage Arrays
To open the ACU, start the
ICP RAID Configuration
utility (see page 84).
If you have more than
one controller, select your controller, then press Enter. Select Array Configuration Utility, then
press Enter.
Follow the on-screen instructions to create and manage arrays, and initialize, rescan, and erase
disk drives.
Creating a New Array
To begin creating an array, select Create Arrays from the main ACU menu.
Only disk drives that can be used in a new array are available for selection. (Disk drives must be
initialized before they can be used in an array. See Initializing Disk Drives on page 85 for more
information.)
Use the Array Properties menu to modify the array’s RAID level, size, name, stripe size, and
caching settings.
Note:
For more information about RAID levels and using disk drives to create arrays, see
Choosing a RAID Level on page 30.
- SAS, SATA, and SCSI 1
- RAID Controllers 1
- Installation and 1
- User’s Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- ICP vortex Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Using the ICP Flash Utility 10
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- About Your RAID Controller 15
- Array-level Features 16
- RAID Controller Battery Model 17
- About the ICP5805BL 18
- About the ICP5045BL 19
- About the ICP5085BL 20
- About the ICP5125BR 21
- About the ICP5165BR 22
- About the ICP9085LI 23
- About the ICP5085BR 24
- About the ICP9047MA 25
- About the ICP9087MA 26
- About the ICP9014RO 27
- About the ICP9024RO 28
- Getting Started 29
- Choosing a RAID Level 30
- Selecting Disk Drives 31
- Selecting Cables 32
- SATA Cables 33
- Installation Options 34
- Basic Installation Steps 34
- In this chapter 36
- Installing the Controller 37
- Connecting External Devices 41
- Creating a Bootable Array 42
- Setting the Boot Controller 43
- Creating an Array 43
- Making Your Array Bootable 46
- Installing the Driver and an 47
- Operating System 47
- Creating a Driver Disk 48
- Installing with Windows 49
- Installing with Red Hat Linux 49
- Installing with SUSE Linux 50
- Installing with NetWare 50
- Installing with OpenServer 51
- Installing with Solaris 51
- Installing with UnixWare 52
- Installing with VMware 52
- Installing with FreeBSD 53
- Installing on Windows 56
- Installing on NetWare 56
- Installing on OpenServer 57
- Installing on Solaris 57
- Installing on UnixWare 58
- Installing on VMware 58
- Installing on FreeBSD 59
- Managing Your Storage Space 60
- About ICP Storage Manager 61
- About the ICP Flash Utility 62
- Which Utility Should I Use? 62
- Solving Problems 63
- Troubleshooting Checklist 64
- Silencing the Alarm 64
- Resetting the Controller 66
- In this appendix 67
- ) Web site at www.scsita.org 67
- What is SAS? 68
- What’s a Phy? 69
- What’s a SAS Port? 70
- What’s a SAS Address? 70
- What’s a SAS Connector? 70
- What do SAS Cables Look Like? 70
- Direct-attach Connections 71
- Backplane Connections 71
- SAS Expander Connections 72
- Understanding RAID 74
- Understanding Drive Segments 75
- Non-redundant Arrays (RAID 0) 75
- RAID 1 Arrays 76
- RAID 1 Enhanced Arrays 76
- RAID 10 Arrays 77
- RAID 5 Arrays 78
- RAID 5EE Arrays 79
- RAID 50 Arrays 80
- RAID 6 Arrays 81
- RAID 60 Arrays 81
- Selecting the Best RAID Level 82
- Creating a New Array 84
- Managing Existing Arrays 85
- Initializing Disk Drives 85
- Rescanning Disk Drives 85
- Secure Erasing Disk Drives 86
- Opening a -Select Utility 86
- Applying Changes and Exiting 86
- General Controller Settings 87
- Option Description 88
- Locating Disk Drives 90
- Identifying Disk Drives 90
- Viewing the Event Log 91
- Running the ACU Using Scripts 94
- About Record Mode 95
- Required 96
- ? Description 96
- HotspareDrives=0:0:0,0:1:0 97
- InitializeAll=Yes 97
- ACU exits with an error 98
- Keyword Description 99
- ACU Error Codes 100
- Sample Scripts 101
- System Requirements 104
- Before You Begin 104
- Running the Menu-based IFU 105
- Running the 106
- Connector Reference 110
- Pin Number Signal Description 111
- 22-55-2161 113
- Pin Number 113
- SFF-8087 Connector J5: 120
- SFF-8087 Connector J18: 120
- SFF-8087 Connector J14: 124
- 22-552101 125
- Environmental Specifications 129
- DC Power Requirements 129
- Current Requirements 129
- Index ● 131 131
- Index ● 132 132
- Index ● 133 133
- Index ● 134 134
- Konrad-Zuse-Str.9 135
- 74172 Neckarsulm 135
Produits connexes et manuels pour Contrôleurs périphériques Adaptec ICP5045BL
TOA Electronics TA 1400 manuales
Manuales del propietario y guías del usuario para Receptores y amplificadores TOA Electronics TA 1400.
Ofrecemos 1 manuales en pdf TOA Electronics TA 1400 para descargar gratis por tipos de documentos: Manual de usuario
Toa electronics TA 1400 Manual de usuario (16 paginas)
Marca: Toa-electronics | Categoria: Receivers and Amplifiers | Tamaño: 0.80 MB |
Tabla de contenidos
Más productos y manuales para Receptores y amplificadores TOA Electronics
| Modelos | Tipo de documento |
|---|---|
| M-9000 |
Manual de usuario
TOA Electronics M-9000 User Manual,
84 paginas
|
| W-906A |
Manual de usuario
TOA Electronics W-906A User Manual,
12 paginas
|
| A-903MK2 |
Manual de usuario
TOA Electronics A-903MK2 User Manual,
12 paginas
|
| 9000 Series |
Manual de usuario
TOA Electronics 9000 Series User Manual [es] ,
24 paginas
|
| BG-1120 |
Manual de usuario
TOA Electronics BG-1120 User Manual,
16 paginas
|
| IP-600D |
Manual de usuario
TOA Electronics IP-600D User Manual,
12 paginas
|
| IWSA500-D |
Manual de usuario
TOA Electronics IWSA500-D User Manual,
10 paginas
|
© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels