Adaptec 1891300 - RAID Controller Guide de l'utilisateur Page 108
- Page / 137
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix E: Using the Adaptec Flash Utility ● 108
These switches are available:
● /C <Controller ID>—One or more RAID controller IDs representing the set of RAID
controllers on which to perform the specified command. The default is 0; if the computer
has multiple RAID controllers, the AFU defaults to controller 0 unless you specify
otherwise.
For example:
To specify a single RAID controller ID:
/C 0
To specify multiple IDs separated by commas:
/C 0,2
To indicate all RAID controllers:
ALL
If you are using multiple RAID controllers, you must specify the controller you want by
using the /C switch; otherwise, the AFU displays an error message and exits.
● /D <UFI File Path>—Specifies the path where the UFI files are located. If you do not
specify the /D switch, the AFU looks for (or creates) its UFI files in the default location.
You cannot specify the name of a UFI file, only its path. UFI filenames are predefined,
based on the RAID controller type.
In this example, the AFU saves flash contents from RAID controller 0 to a UFI file in the
current default drive and directory:
A:\> AFU SAVE /C 0
In this example, the AFU saves flash contents from Controller 1 to a UFI file in
C:\UFI_FILES:
A:\> AFU SAVE /C 1 /D C:\UFI_FILES
Update
Updates the flash components of one or more RAID controllers on your computer from the
flash image data in a UFI file. You must restart the computer following an UPDATE command.
The command syntax for the UPDATE command is:
AFU UPDATE [/C<Controller ID>] [/D <UFI File Path>]
This example shows a typical system response after an update.
A:\> AFU UPDATE /C 0
Adaptec Flash Utility V4.0-0 B5749
(c)Adaptec Inc. 1999–2005. All Rights Reserved.
Updating Controller 0 (Adaptec 2820)
Reading flash image file (Build 5749)
AFU is about to update firmware on controllers Adaptec Adaptec 2230SLP
***PLEASE DO NOT REBOOT THE SYSTEM DURING THE UPDATE***
This might take a few minutes.
Writing Adaptec Adaptec 2230SLP (4MB) Flash Image to controller 0...OK.
Verifying...OK
Please restart the computer to allow firmware changes to take effect.
- Installation and User’s Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- About Your RAID Controller 15
- Array-level Features 16
- Adding Enhanced Features 17
- About the Adaptec 3085 18
- About the Adaptec 3405 19
- About the Adaptec 3805 20
- About the Adaptec 31205 21
- About the Adaptec 31605 22
- Mode 0 Flash connector 22
- About the Adaptec 4000 23
- About the Adaptec 4800SAS 24
- 256 MB also available 24
- About the Adaptec 4805SAS 25
- About the Adaptec 2420SA 26
- About the Adaptec 2820SA 27
- About the Adaptec 2130SLP 28
- About the Adaptec 2230SLP 29
- Getting Started 30
- Choosing a RAID Level 31
- Selecting Disk Drives 32
- Selecting Cables 33
- SATA Cables 34
- Installation Options 35
- Basic Installation Steps 35
- In this chapter 37
- Installing the Controller 38
- Connecting External Devices 42
- Creating a Bootable Array 43
- Setting the Boot Controller 44
- Creating an Array 44
- Making Your Array Bootable 47
- Installing the Driver and an 48
- Operating System 48
- Creating a Driver Disk 49
- Installing with Windows 50
- Installing with Red Hat Linux 50
- Installing with SUSE Linux 51
- Installing with NetWare 51
- Installing with OpenServer 52
- Installing with Solaris 52
- Installing with UnixWare 53
- Installing with VMware 53
- Installing with FreeBSD 54
- Installing on Windows 57
- Installing on NetWare 57
- Installing on OpenServer 58
- Installing on Solaris 58
- Installing on UnixWare 59
- Installing on VMware 59
- Installing on FreeBSD 60
- Managing Your Storage Space 61
- About Adaptec Storage Manager 62
- Which Utility Should I Use? 63
- Solving Problems 64
- Troubleshooting Checklist 65
- Silencing the Alarm 65
- Resetting the Controller 67
- ) Web site at www.scsita.org 68
- In this appendix 68
- What is SAS? 69
- What’s a Phy? 70
- What’s a SAS Port? 71
- What’s a SAS Address? 71
- What’s a SAS Connector? 71
- What do SAS Cables Look Like? 71
- Direct-attach Connections 72
- Backplane Connections 72
- SAS Expander Connections 73
- Understanding RAID 75
- Understanding Drive Segments 76
- Non-redundant Arrays (RAID 0) 76
- RAID 1 Arrays 77
- RAID 1 Enhanced Arrays 77
- RAID 10 Arrays 78
- RAID 5 Arrays 79
- RAID 5EE Arrays 80
- RAID 50 Arrays 81
- RAID 6 Arrays 82
- RAID 60 Arrays 82
- Selecting the Best RAID Level 83
- Using the Adaptec RAID 84
- Configuration Utility 84
- Running the ARC Utility 85
- Managing Existing Arrays 86
- Initializing Disk Drives 86
- Rescanning Disk Drives 86
- Secure Erasing Disk Drives 87
- Opening a -Select Utility 87
- Applying Changes and Exiting 87
- General Controller Settings 88
- Option Description 89
- Locating Disk Drives 91
- Identifying Disk Drives 91
- Viewing the Event Log 92
- Running the ACU Using Scripts 95
- About Record Mode 96
- Required 97
- ? Description 97
- HotspareDrives=0:0:0,0:1:0 98
- InitializeAll=Yes 98
- ACU exits with an error 99
- Keyword Description 100
- ACU Error Codes 101
- Sample Scripts 102
- System Requirements 105
- Before You Begin 105
- Running the Menu-based AFU 106
- Running the 107
- I2C Connector Reference 111
- Pin Number Signal Description 112
- 22-55-2161 114
- Pin Number 114
- SFF-8087 Connector J5: 125
- SFF-8087 Connector J18: 125
- SFF-8087 Connector J14: 125
- 22-552101 126
- SFF-8484 Connector J7: 128
- Electrostatic Discharge (ESD) 129
- Environmental Specifications 131
- DC Power Requirements 131
- Current Requirements 131
- Index ● 133 133
- Index ● 134 134
- Index ● 135 135
- Index ● 136 136
- Adaptec, Inc 137
- 691 South Milpitas Boulevard 137
- Milpitas, CA 95035 USA 137
Produits connexes et manuels pour Contrôleurs périphériques Adaptec 1891300 - RAID Controller
(113 pages)Zanussi ZWG7160P manuels
Manuels d'utilisation et guides de l'utilisateur pour Machines à laver Zanussi ZWG7160P.
Nous fournissons des manuels en pdf 13 Zanussi ZWG7160P à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels