Adaptec GDT8546RZ Guide de l'utilisateur Page 1

PreliminaryICP RAID ControllerGDT8546RZ and GDT8586RZFour-port Low Profile Serial ATA RAID ControllerHardware Installation and User’s Guide, Version 1

10 Hardware Installation and User’s GuideHardware InstallationHardware Installation2This chapter provides information on installing the ICP RAID contr

Hardware Installation and User’s Guide 11Hardware InstallationFigure 2-1. ICP RAID Controller Component Layout GDT8546RZ

Figure 2-2. ICP RAID Controller Layout GDT8586RZ2.1.2 Installing the ICP RAID Controller1. Power-off the computer system.2. Disconnect power cord(s)

Hardware Installation and User’s Guide 13Hardware InstallationFigure 2-3. Installing the ICP RAID Controller into a Computer System2.1.3 Changing Jump

14 Hardware Installation and User’s GuideHardware InstallationFigure 2-4. Jumper Locations and Pin Numbers (GDT8546RZ)231PCI Bus Speed (J4)Auto-negoti

Hardware Installation and User’s Guide 15Hardware InstallationJ1 - IOP mode select jumper block: This jumper is used to place the IOP in reset, which

2.2 Diagnosis FunctionsThe GDT8546RZ and GDT8586RZ have LED indicators, an 80db audible alarm, and boot-up beep sequences that can help diagnose the c

Hardware Installation and User’s Guide 17Hardware Installation2.2.2 Audible AlarmAn 80db audible alarm, which is controlled by the RAID firmware, is m

18 Hardware Installation and User’s GuideHardware InstallationIf the cause of the event is resolved and/or removed, the audible alarm will cease. You

Hardware Installation and User’s Guide 19Hardware Specifications and FeaturesHardware Specifications and Features3This chapter covers all the hardware

Hardware Installation and User’s GuideIMPORTANT NOTICE - READ BEFORE MAKING USE OF THE INFORMATION CONTAINED HEREINThis information is provided “as is

20 Hardware Installation and User’s GuideHardware Specifications and FeaturesPCI Transfer Rate 528 MB/sec (Burst) DMA to PCI and local buses PCI Signa

Hardware Installation and User’s Guide 21Hardware Specifications and Features3.2 Operating System SupportThe following operating systems are fully val

22 Hardware Installation and User’s GuideHardware Specifications and FeaturesNote:For a migrated RAID array to be recognized by the new host operating

Hardware Installation and User’s Guide 23Hardware Specifications and Features• Cabling that meets SATA specifications 1.0Physical drives are limited b

24 Hardware Installation and User’s GuideFlash Memory ProgrammingFlash Memory Programming AA.1 About Firmware FilesThe firmware image that is stored i

Hardware Installation and User’s Guide 25Flash Memory ProgrammingRefer to Section A.2 for help in deciding whether the firmware needs a recovery or up

26 Hardware Installation and User’s GuideFlash Memory ProgrammingThe FRUU is available from these locations:A.4.1 Creating Firmware Diskettes from the

Hardware Installation and User’s Guide 27Flash Memory Programming10. After the file transfer is complete, remove the firmware diskette from the comput

28 Hardware Installation and User’s GuideFlash Memory Programming4. Insert the RAID Software Suite CD-ROM.ORInsert the bootable FRUU floppy.5. Boot th

Hardware Installation and User’s Guide 29Flash Memory ProgrammingA.5 Updating Firmware Using XROM ICPCONThere are two options for updating the firmwar

Hardware Installation and User’s Guide 3Contents1 Getting Started1.1 Using the User Documentation Set ...

30 Hardware Installation and User’s GuideFlash Memory Programming10.ICPCON detects the firmware update and requires a system reboot. Press any key to

4 Hardware Installation and User’s GuideIndexFigures2-1 ICP RAID Controller Component Layout GDT8546RZ...

Hardware Installation and User’s Guide 5Getting StartedGetting Started1Intended AudienceThis documentation is intended for users who are experienced i

6 Hardware Installation and User’s GuideGetting Startedthe software and firmware For further information refer to the Optional Features section of the

Hardware Installation and User’s Guide 7Getting Started1.4 Regulatory and Certification InformationNote:This controller is intended for use in UL List

8 Hardware Installation and User’s GuideGetting StartedThis equipment has been tested and found to comply with the limits for aClass B digital device,

Hardware Installation and User’s Guide 9Getting StartedSuomi Tämä tuote noudattaa EU-direktiivin 89/336/EEC & 73/23/EEC määräyksiä.Français Ce p