USER’S REFERENCEADAPTEC SCSI CARD 29160ULTRA160 SCSI CONTROLLER

4Adaptec SCSI Card 29160 User’s Reference Termination on non-Ultra160 and Ultra2 internal SCSI devices usually is controlled by manually setting a jum

5TroubleshootingTroubleshootingMost problems can be resolved by following the recommendations in the Troubleshooting Checklist below. If you still exp

6Adaptec SCSI Card 29160 User’s ReferenceTroubleshooting in Windows 95/98When I start Windows 95/98, the system locks up when the Windows logo is disp

7Troubleshooting4Double-click the SCSI Controller icon. The software driver for the Adaptec SCSI Card 29160 is listed as 29160, 29160N, 29160B, CPQ291

8Adaptec SCSI Card 29160 User’s ReferenceIf Windows 95/98 does not detect the Adaptec SCSI Card 29160, get the driver disk or CD included with the SCS

9Troubleshooting If a resource is used by an unknown device, the resource is used but the device using the resource cannot be detected. (This conditio

10Adaptec SCSI Card 29160 User’s ReferenceCommon Error MessagesHere is what you should do if the following messages appear at bootup:“Device connected

11TroubleshootingSCSISelect termination option for the SE connector to Automatic or Enable.“Attention! Insufficient termination detected on the SE con

12Adaptec SCSI Card 29160 User’s ReferenceUsing the Adaptec SCSI Card 29160 and SCSI DevicesThis section provides useful information on using the Adap

13Using the Adaptec SCSI Card 29160 and SCSI DevicesUsing Ultra160 Hard Disk Drives We recommend that you connect your LVD (Ultra160 and Ultra2) SCSI

RAdaptec, Inc.691 South Milpitas BoulevardMilpitas, CA 95035© 2000 Adaptec, Inc. Adaptec, Inc.All rights reserved. Adaptec and the Adaptec logo are tr

14Adaptec SCSI Card 29160 User’s ReferenceCombining SCSI and Non-SCSI DevicesYou can install the Adaptec SCSI Card 29160 in a computer that already ha

15Using the Adaptec SCSI Card 29160 and SCSI DevicesInstalling Multiple SCSI Cards You can install multiple SCSI cards in your computer; you are limit

16Adaptec SCSI Card 29160 User’s ReferenceConfiguring the Adaptec SCSI Card 29160 with SCSISelectSCSISelect, included with the Adaptec SCSI Card 29160

17Configuring the Adaptec SCSI Card 29160 with SCSISelectEnable Disconnection Yes, No Yes (Enabled)Send Start Unit Command Yes, No Yes (Enabled)Enable

18Adaptec SCSI Card 29160 User’s ReferenceStarting SCSISelectFollow these steps to start SCSISelect:1Turn on or restart your system.During the startup

19Configuring the Adaptec SCSI Card 29160 with SCSISelectSCSI Bus Interface Definitions Host Adapter SCSI ID—(Default: 7) Sets the SCSI ID for the SCS

20Adaptec SCSI Card 29160 User’s Reference Initiate Wide Negotiation—(Default: Ye s) When set to Yes, the SCSI card attempts 16-bit data transfer (wid

21Configuring the Adaptec SCSI Card 29160 with SCSISelectAdvanced Configuration OptionsNote: Do not change the Advanced Configuration Options unless a

22Adaptec SCSI Card 29160 User’s Reference Set to Disabled: Not scan if the devices on the SCSI bus (for example, CD-ROM drives) are controlled by sof

23Configuring the Adaptec SCSI Card 29160 with SCSISelect BIOS Support for Int 13 Extensions—(Default: Enabled) When set to Enabled, the SCSI card BIO

R▼ ▼ ▼ ▼ Adaptec SCSI Card 29160Ultra160 SCSI ControllerUser’s Reference

24Adaptec SCSI Card 29160 User’s ReferenceConnecting SCSI DevicesHere are some examples of how you can connect internal and exter-nal SCSI devices to

25Connecting SCSI DevicesThe following example shows two Ultra160/Ultra2 SCSI devices connected to the external connector. As in the previous diagrams

27Copyright© 2000 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in an

28Adaptec Customer SupportIf you have questions about installing or using your Adaptec product, check this User’s Reference first—you will find answer

29Regulatory Compliance StatementsFederal Communications Commission Radio Frequency Interference StatementWARNING: Changes or modifications to this un

30Canadian Compliance StatementThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.Cet ap

31Adaptec Software License AgreementIn return for acquiring a license to use the software (“Software”) and related documentation, you agree to the fol

329 Export: You acknowledge that the laws and regulations of the United States restrict the export and re-export of the Software. You agree that you w

iiiOverview 1Ultra160 SCSI on the Adaptec SCSI Card 29160 1Understanding SCSI 2SCSI IDs 2Terminating the SCSI Bus 3Troubleshooting 5Troubleshooting Ch

ivAdaptec SCSI Card 29160 User’s ReferenceConfiguring the Adaptec SCSI Card 29160 with SCSISelect 16Starting SCSISelect 18Exiting SCSISelect 18Using S

1OverviewUltra160 SCSI on the Adaptec SCSI Card 29160The Adaptec SCSI Card 29160 supports Ultra160 SCSI devices. Ultra160 is a new generation of SCSI

2Adaptec SCSI Card 29160 User’s ReferenceNote: Read the Adaptec SCSI Card 29160 Installation Guide if you need instructions on installing the SCSI Car

3Overview SCSI ID 7 has the highest priority on the SCSI bus. The priority of the remaining IDs, in descending order, is 6 to 0, then 15 to 8. The Ada