Adaptec USBXchange Guide de l'utilisateur

User’s GuideUSBXchange™ Copyright© 2000 Adaptec Inc. All rights reserved. The user may print one copy for personal use. Production of multiple copies

User’s Guide: USBXchange • 104 Select Search for a suitable driver... and then click Next.5 Select CD-ROM drives for the Found New Hardware Wizard to

User’s Guide: USBXchange • 116 Click Next to install the driver. 7 Click Finish to complete the installation.

User’s Guide: USBXchange • 12Uninstalling the USBXchange Driver for Windows 98 and Windows 2000Follow these steps to uninstall your USBXchange driver:

User’s Guide: USBXchange • 136 A Windows dialog box will appear when you have successfully uninstalled the USBXchange driver: USBXchange Power SupplyT

User’s Guide: USBXchange • 14If you click Yes , you may receive this message: You can try either of the following to correct the problem:♦ Unplug th

User’s Guide: USBXchange • 15Your external DC power jack can be plugged into the DC input jack connection located on the side of the USBXchange. Insta

User’s Guide: USBXchange • 16Connecting a SCSI Device1 Ensure that your SCSI device is turned off.2 Connect the USBXchange to the SCSI device.Dependin

User’s Guide: USBXchange • 17Connecting to the USB Port1 Connect the USBXchange to the USB port.2 Make sure the cable ends are firmly connected. Do no

User’s Guide: USBXchange • 18Using USBXchange SwitcherUSBXchange Switcher is a control panel which allows you to use your driver for either Mass Stora

User’s Guide: USBXchange • 19Viewing SCSI Devices on Your MacintoshNote: If your are operating in Mass Storage mode you will not see any devices in SC

User’s Guide: USBXchange • 2IntroductionThis user’s guide explains how to use the USBXchange to allow SCSI devices to plug into the Universal Serial B

User’s Guide: USBXchange • 20USBXchange Power SupplyThe USBXchange receives its power from either the termination power line of attached SCSI devices

User’s Guide: USBXchange • 21External DC Power SupplyIf you need an external power source, the USBXchange can use a DC power jack with 4.5V–9V output

User’s Guide: USBXchange • 22Understanding SCSISCSI (pronounced “scuzzy”) stands for Small Computer System Interface. SCSI is an industry standard com

User’s Guide: USBXchange • 23There are various methods for terminating hard disk drives and other SCSI devices. Read the device documentation if you a

User’s Guide: USBXchange • 24Follow these steps to connect to more than one SCSI device:1 Follow the steps in the section Connecting to the USB Port o

User’s Guide: USBXchange • 25TroubleshootingIf you have problems with the USBXchange, check these troubleshooting tips:My device is not recognized. Ho

User’s Guide: USBXchange • 26When I power off/on my SCSI device while still connected to USBXchange, the system does not detect the USBXchange or the

User’s Guide: USBXchange • 27Copyright© 2000 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval s

User’s Guide: USBXchange • 28Adaptec Customer SupportIf you have questions about installing or using your Adaptec product, check this user’s guide fir

User’s Guide: USBXchange • 29Stock No. 512545-00, Ver. AA JG 6/00Regulatory Compliance StatementsFederal Communications Commission Radio Frequency Int

User’s Guide: USBXchange • 3Note: Adaptec strongly recommends that you plug the USBXchange directly into a USB port on your system. If you must connec

User’s Guide: USBXchange • 4To locate specific information covered in this user’s guide, refer to the following table:For information about… Go to…PC

User’s Guide: USBXchange • 5Installing the USBXchange on PC CompatiblesThe USBXchange is easy to install and use. To avoid any problems during the ins

User’s Guide: USBXchange • 6Connecting to the USB Port1 After connecting to your SCSI devices, if your computer is not powered up, then power it up no

User’s Guide: USBXchange • 72 Connect the USB connector of your USBXchange to a port on the external USB hub. Installing the Windows 98 DriverWhen you

User’s Guide: USBXchange • 84 Select Search for the best driver... and then click Next. 5 Select CD-ROM drive for the Add New Hardware Wizard to searc

User’s Guide: USBXchange • 97 Click Finish to complete the installation. Installing the Windows 2000 DriverWhen you attach the USBXchange, Windows 200